Which address should I use to log in to a Hyperoptic router?

The default login address is 192.168.1.1. Enter it in the address bar of your browser to open the login page. If that does not work, try 192.168.0.1 or 192.168.100.1.

What are the default login credentials for Hyperoptic router?

The most commonly reported default credentials are username admin. These may have been changed by your ISP or during a previous setup. Check the sticker on the router if they do not work.

What can I do if 192.168.1.1 does not open?

Confirm that your device is connected directly to the router. Check the address for typos. Restart the router and wait about 30 seconds. Disable any VPN or proxy connections. If the problem persists, look up the correct gateway address in the network settings of your device.

How do I reset a Hyperoptic router to factory settings?

Press and hold the reset button on the back of the router for at least 10 seconds. The router will restart with factory defaults, including the original login credentials. Note that this will also erase any custom settings.

I have multiple routers — which one am I logging into?

Make sure you are connected to the specific router you want to configure. Each device on the network may have a different admin address. Check which gateway your device is currently using in the network settings.

Brand

Hyperoptic Router Login

This page covers how to log in to a Hyperoptic router and configure common settings. The admin panel is usually available at 192.168.1.1. You will find the default login address, common credentials, and instructions for changing Wi-Fi settings.

Hyperoptic

// router overview

Hyperoptic provides fiber broadband with router models like ZTE H298A, ZTE H298N, Tilgin HG2381, and Nokia HA-140W-B. Login is typically via 192.168.1.1 with the username 'admin'. Wi-Fi and admin settings vary slightly by model.

Manufacturer: Hyperoptic
Device type: router
Common models: ZTE H298A, ZTE H298N, Tilgin HG2381, Nokia HA-140W-B
Firmware: Hyperoptic Custom Firmware · UK

Hyperoptic routers like the ZTE H298A and Nokia HA-140W-B have model-specific menus for Wi-Fi settings, unlike generic routers. The lack of a default password is also notable, requiring users to set one during initial setup.

Web interface

// common ip addresses

192.168.1.1PrimaryOn record 192.168.0.1Alternative IP for some models 192.168.100.1Less common, but documented for certain configurations

Models on record

// models

ZTE H298AUses Local Network > WLAN > WLAN Basic for Wi-Fi settings
ZTE H298NUses Network > WLAN > SSID Settings for Wi-Fi configuration
Tilgin HG2381Uses Wireless > SSID Configuration for Wi-Fi changes
Nokia HA-140W-BUses Network > Wireless (2.4GHz/5GHz) for Wi-Fi settings

Log in to your Hyperoptic router

// login steps

01
Open the Hyperoptic web interface at 192.168.1.1 or 192.168.0.1 or 192.168.100.1.
02
Open a browser and type 192.168.1.1 in the address bar.
03
Enter the Username: admin and Password and click Login.
04
You will be logged in to the Hyperoptic WebGUI.

Change the Wi-Fi password on Hyperoptic

// wifi key

01
Log in to the router settings using 192.168.1.1 and the username 'admin'.
02
Navigate to the Wi-Fi security settings (WLAN > Security for ZTE models, SSID > Security for Tilgin, or Wireless > Security for Nokia).
03
Enter the new Wi-Fi password in the 'WPA Passphrase' or 'WPA Key' field.
04
Click 'Submit' or 'Apply' to save changes.

Change the Wi-Fi name on Hyperoptic

// wifi name

01
Log in to the router settings using 192.168.1.1 and the username 'admin'.
02
Navigate to the Wi-Fi settings (varies by model: Local Network > WLAN > WLAN Basic for ZTE H298A, Network > WLAN > SSID Settings for ZTE H298N, Wireless > SSID Configuration for Tilgin HG2381, or Network > Wireless for Nokia HA-140W-B).
03
Enter the new Wi-Fi Network Name (SSID) in the designated field.
04
Click 'Submit' or 'Apply' to save changes.

Factory reset this Hyperoptic

// factory reset

01
Locate the reset button on the back of the router (usually a small pinhole).
02
Use a paperclip to press and hold the reset button for 10-15 seconds.
03
Wait for the router to reboot (all lights will flash and stabilize).
04
Reconfigure the router using default settings (login with 'admin' and no password).

Change the admin password on Hyperoptic

// admin password

01
Log in to the router settings using 192.168.1.1 and the username 'admin'.
02
Navigate to the Administration or System Tools section (exact path varies by model).
03
Locate the 'Change Password' or 'Admin Password' option.
04
Enter the current password (if prompted) and the new password twice.
05
Click 'Save' or 'Apply' to confirm the change.

Device information

// device intel

ZTE H298A

You need to configure 2.4GHz and 5GHz Wi-Fi parameters separately.

If the login page does not open

// diagnostics

Having trouble accessing your Hyperoptic router settings? Connection issues, rejected credentials, and slow-loading admin pages are common problems. Below are the most frequent issues and how to fix them quickly.

Frequently asked questions

// faq

Related routers and IP addresses

// related

Pages that share this brand or this address.

IP addresses

192.168.1.1

All IPs All brands All hosts

Brands

Hyperoptic

Web interface

Models on record

Log in to your Hyperoptic router

Change the Wi-Fi password on Hyperoptic

Change the Wi-Fi name on Hyperoptic

Factory reset this Hyperoptic

Change the admin password on Hyperoptic

Device information

ZTE H298A

If the login page does not open

Can't access 192.168.1.1

Wi-Fi not working after changes

192.168.1.1 is not reachable

Login credentials are not accepted

The page loads very slowly or times out

Wrong IP address?

How to reset the router to factory settings